( 1 /9) 2000 - 06 - 06 (ver.4.0) liquid crystal display division product information features (1) 10.4 ? svga color display with high luminance (2) built in long life lamps(30,000 h) (3) replaceable structure of lamp units (4) full mechanical compatible with ltm10c209h, ltm10c209a (10.4 ? vg a) mechanical specifications item specifications dimensional outline (typ.) 265.0( w ) x 188.8( h ) x 12max( d ) mm number of pixels 800( w ) x 600( h ) pixels active area 211.2( w ) x 158.4( h ) mm pixel pitch 0.264( w ) x 0.264( h ) weight (approximately) 580g back light twin ccfls, sidelight type absolute maximum ratings item min. max. unit ( v dd ) - 0.3 7.0 v supply voltage ( v fl ) 0 2.0 kv(rms) fl driving frequency ( f fl ) 0 100 khz input signal voltage ( v in ) - 0.3 v dd +0.3 v operating temperature 0 50 c storag e temperature - 20 60 c storage humidity (max. wet bulb temperature = 39 c) 10 90 %(rh) electrical specification ( t a=25 c) item min. typ. max. unit remarks ( v dd ) 4.75 5.0 5.25 v supply voltage ( v fl ) 500 550 600 v(rms) fl start voltage 1500 --- 1 800 v(rms) t a=0 c high level input voltage ( v ih ) 3.5 --- v dd low level input voltage ( v il ) 0 --- 1.5 v *1 ( i dd ) --- 200 320 ma current consumption *2 ( i fl ) 3.0 6.0 7.0 ma(rms) *1 *2 power consumption --- 7.6 --- w i fl =6.0marms *1 : 8 colo r bars pattern *2 : except the efficiency of fl inverter optical specification ( t a=25 c) item min. typ. max. unit remarks contrast ratio ( cr ) 100 250 --- --- ( t on ) --- --- 50 ms response time ( t off ) --- --- 50 ms luminance ( l ) 190 250 --- cd/m 2 i fl =6.0marms *the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by toshiba or other rights of the third parties which may result from its use. no license is granted by im plication or otherwise under any patent or patent rights of toshiba or others. *the information contained herein may be changed without prior notice. it is therefore advisable to contact toshiba before proceeding with the design of equipment incorporating this product. 26cm colour tft - lcd module (10.4 type) LTM10C273 (a - si tft) tentative www..net
( 2 /9) 2000 - 06 - 06 (ver.4.0) LTM10C273 dimensional outline tentative unit : mm standard tolerance : 0.5 f 3 . 5 3 3 3 3 . 5 2 5 9 0 . 4 2 5 2 . 0 ( 2 6 2 . 0 ) + _ 3 . 0 3 . 5 1 9 . 9 1 2 8 . 0 2 1 6 . 2 ( b e z e l o p e n n i n g ) ( a c t i v e / v i e w i n g a r e a c e n t e r ) 0 . 4 1 3 0 . 0 6 5 . 0 ( a c t i v e / v i e w i n g a r e a c e n t e r ) + _ 1 6 3 . 4 ( b e z e l o p e n n i n g ) 1 6 1 . 1 8 . 0 1 5 8 . 4 ( a c t i v e a r e a ) 3 . 5 3 . 5 3 . 0 3 . 5 4 - 3 . 2 7 . 0 8 . 0 7 . 0 1 2 . 0 m a x 2 . 5 4 . 5 2 6 5 . 0 2 1 5 . 2 ( v i e w i n g a r e a ) 2 1 1 . 2 ( a c t i v e a r e a ) 1 6 2 . 4 ( v i e w i n g a r e a ) 0 . 4 1 3 0 + _ 1 2 7 . 0 1 8 8 . 6 9 9 ( 2 5 3 . 0 ) 2 7 . 5 1 0 . 8 ( 2 . 7 )
( 3 /9) 2000 - 06 - 06 (ver.4.0) LTM10C273 dimensional outline tentative unit : mm standard tolerance : 0.5 8 0 ? } 1 0 b e z e l s u r f a c e u s e r s i d e c o n n e c t o r i / f c o n n e c t o r 4 m m m a x h e i g h t c o m p o n e n t s a r e p l a c e d ; 3 8 . 0 2 . 5 3 . 0 4 . 0 4 . 0 3 . 0 3 . 0 4 . 0 3 . 0 4 . 0 3 . 0 4 . 0 4 . 0 4 . 0 4 . 0 4 . 0 4 . 0 3 . 0 4 . 0 - ? 4 8 0 ? } 1 0 1 5 . 0 7 . 0 ? } 0 . 5 p c b c n 1 n o . 1 n o . 3 1 1 0 . 0 2 0 . 0 n o . 2 ( f r a m e ) l o w v o l t a g e h i g h v o l t a g e n o . 1 n o . 3 ?b ?m ?q ?b ?m ?r s e c t i o n a l f i g u r e o f i / f c o n n e c t o r n o . 1 n o . 1 n o . 3 h i g h v o l t a g e l o w v o l t a g e
( 4 /9) 2000 - 06 - 06 (ver.4.0) LTM10C273 block diagram v bb v gg connector dc/dc converter panel controller gray scale manipulation voltage generation circuit y - driver ic liquid crystal panel 800 x 600 pixels x - driver ic cn2 cn1 backlight backlight cn3
( 5 /9) 2000 - 06 - 06 (ver.4.0) LTM10C273 timing chart t 3 ( 2 ) h o r i z o n t a l t i m i n g ( 1 ) v e r t i c a l t i m i n g e n a b n c l k g 5 - g 0 r 5 - r 0 b 5 - b 0 e n a b n c l k r 5 - r 0 g 5 - g 0 b 5 - b 0 t c t 4 t 3 t 3 t 2 t 1 4 , y 3 , y 2 , y 1 , y x , 4 x , 3 x , 2 x , 1 x , y x , y 7 , y 6 , y 5 , y 8 0 0 , y 7 9 9 , y 7 9 8 , y 7 9 7 , y x , 6 0 0 x , 5 9 9 x , 5 9 8 a d d 0 . 5 v d d i n p u t s i g n a l c e n t e r l e v e l : 0 . 5 v i l v ( m a x ) : 1 . 5 ( v ) i h v ( m i n ) : 3 . 5 ( v ) i l v ( m a x ) : 1 . 5 ( v ) i h v ( m i n ) : 3 . 5 ( v ) _ + d u t y ( a , b ) : 5 0 1 0 % n c l k b d a t a v a l i d t 9 t 8 t 7 t 5 n c l k b 5 - b 0 g 5 - g 0 r 5 - r 0 e n a b t 6
( 6 /9) 2000 - 06 - 06 (ver.4.0) LTM10C273 timing specification 1) 2) 3) 4) 5) item symbol min. typ. max. unit remarks frame period t 1 604 x t 3 625 x t 3 17.78 628 x t 3 17.86 --- ms vertical display term t 2 600 x t 3 600 x t 3 600 x t 3 --- t 2=n x t 3 one line scanning time t 3 844 x tc 26. 4 1024 x tc 28.44 1056 x tc --- --- m s horizontal display term t 4 800 x tc 800 x tc 800 x tc --- clock period tc 25.0 27.78 --- ns clock ? l ? time t 6 9.0 --- --- ns clock ? h ? time t 7 9.0 --- --- ns set up time t 8 4.0 --- --- ns hold time t 9 5. 0 --- --- ns note 1) when enab is fixed to ? h ? level or ? l ? level after nclk input, the panel is displayed as black. however, it may be occurred a flicker on the display. note 2) when nclk is fixed to ? h ? level or ? l ? level, the panel becomes white s tage after several seconds. note 3) do not change t1 and t3 values in the operation. when t1 or t3 is changed, the panel is displayed as black. note 4) please adjust lcd operating signal timing and fl driving frequency, to optimize the display quality. there is a possibility that flicker is observed by the interference of lcd operating signal timing and fl driving condition (especially driving frequency). note 5) the following conditions should be met. a. nclk count of each horizontal scanning time sho uld be always the same. b. v - blanking period should be "n" x "horizontal scanning time". (n=integer) c. frame period should be always the same. 1, 1 2, 1 x, 1 800, 1 1, 2 1, y x, y 1, n 800, n 800 pixels 600 l ines
( 7 /9) 2000 - 06 - 06 (ver.4.0) LTM10C273 connector pin assignment for interface cn1 input signal connector : df9b - 31p - 1v / hirose electric co., ltd. mat ing connector : df9* - 31s - 1v / hirose electric co., ltd. ( * : option mark) terminal no. symbol function 1 gnd 2 nclk sampling clock 3 gnd 4 r0 red display data (lsb) 5 r1 red display data 6 r2 red display data 7 gnd 8 r3 red display data 9 r4 red display data 10 r5 red display data (msb) 11 gnd 12 g0 green display data (lsb) 13 g1 green display data 14 g2 green display data 15 gnd 16 g3 green display data 17 g4 green display data 18 g5 green display dat a (msb) 19 gnd 20 enab compound synchronization signal 21 gnd 22 b0 blue display data (lsb) 23 b1 blue display data 24 b2 blue display data 25 gnd 26 b3 blue display data 27 b4 blue display data 28 b5 blue display data (msb) 29 gnd 30 v dd +5v power supply 31 v dd +5v power supply cn2 ccfl power source connector : bhr - 03vs - 1 / japan solderless terminal mfg co., ltd. mating connector : sm02(8.0)b - bhs - 1 / japan solderless terminal mfg co., ltd. terminal no. symbol function 1 v flh1 ccfl power supply ( high voltage) 2 nc 1) non connection (open) 3 v fll1 ccfl power supply (low voltage) cn3 ccfl power source connector : bhr - 03vs - 1 / japan solderless terminal mfg co., ltd. mating connector : sm02(8.0 )b - bhs - 1 / japan solderless terminal mfg co., ltd. terminal no. symbol function 1 v flh2 ccfl power supply ( high voltage) 2 nc 1) non connection (open) 3 v fll2 ccfl power supply (low voltage) note 1) nc terminal should be open.
( 8 /9) 2000 - 06 - 06 (ver.4.0) tm10c273 256k (k=1024) colors combination table display r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 gray scale level black l l l l l l l l l l l l l l l l l l - blue l l l l l l l l l l l l h h h h h h - green l l l l l l h h h h h h l l l l l l - light blue l l l l l l h h h h h h h h h h h h - red h h h h h h l l l l l l l l l l l l - purple h h h h h h l l l l l l h h h h h h - yellow h h h h h h h h h h h h l l l l l l - basic color wh ite h h h h h h h h h h h h h h h h h h - black l l l l l l l l l l l l l l l l l l l 0 l l l l l h l l l l l l l l l l l l l 1 l l l l h l l l l l l l l l l l l l l 2 : : : : : : l3 ? l60 h h h h l h l l l l l l l l l l l l l61 dark - light h h h h h l l l l l l l l l l l l l l62 gray scale of red red h h h h h h l l l l l l l l l l l l red l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l l l l l l l h l l l l l l l 1 l l l l l l l l l l h l l l l l l l l 2 : : : : : : l3 ? l60 l l l l l l h h h h l h l l l l l l l61 dark - light l l l l l l h h h h h l l l l l l l l62 gray scale of green green l l l l l l h h h h h h l l l l l l green l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l l l l l l l l l l l l l h l 1 l l l l l l l l l l l l l l l l h l l 2 : : : : : : l3 ? l60 l l l l l l l l l l l l h h h h l h l61 dark - light l l l l l l l l l l l l h h h h h l l6 2 gray scale of blue blue l l l l l l l l l l l l h h h h h h blue l63 black l l l l l l l l l l l l l l l l l l l 0 l l l l l h l l l l l h l l l l l h l 1 l l l l h l l l l l h l l l l l h l l 2 : : : : : : l3 ? l60 h h h h l h h h h h l h h h h h l h l61 dark - light h h h h h l h h h h h l h h h h h l l62 gray scale of white & black white h h h h h h h h h h h h h h h h h h white l63
( 9 /9) 2000 - 06 - 06 (ver.4.0) ltm10c2 73 for safety lcd module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. in using our modules, make certain that you fully understand and put into practice the warnings and safety precautions de tailed in engineering information no.ee - n001,"cautions and instructions for toshiba lcd modules". refer to individual specifications and technical data sheets (hereinafter called "td") for more detailed technical information. 1) special purposes a) toshiba 's standard lcd modules have not been customized for operation in extreme environments or for use in applications where performance failures could be life - threatening or otherwise catastrophic. b) since toshiba's standard lcd modules have not been designe d for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed toshiba's published specification limits. c) in addition, since toshiba standard lcd modules have not been designed for use in applications where performance failures could be life - threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to traffic collision avoidance system and air tra ffic indicator), in military defense or weapons systems, in critical industrial process - control systems (e.g., those involved in the production of nuclear energy), or in critical medical device or patient life - support systems. 2) disassembling or modificatio n do not disassemble or modify the module. it may damage sensitive parts inside lcd module, and may cause scratches or dust on the display. toshiba doses not warrant the module, if customer disassembled or modified it. 3) breakage of lcd panel do not inges t liquid crystal material, do not inhale this material, and do not contact the material with skin, if lcd panel is broken and liquid crystal material spills out. if liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immedi ately. if this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. 4) glass of lcd panel be careful with chips of glass that may cause injuring fingers or skin, when the glass is broken. 5) electric shoc k disconnect power supply before handling lcd module. do not touch the parts inside lcd module and the fluorescent lamp's connector or cables in order to prevent electric shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on. 6) absolute maximum ratings and power protection circuit do not exceed the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' con stants, environmental temperature, etc., otherwise lcd module may be damaged. employ protection circuit for power supply, whenever the specification or td specifies it. suitable protection circuit should be applied for each system design. 7) disposal when di spose lcd module, obey to the applicable environmental regulations. !
|
